Search Messages

 
Author:
Search Start Date:
Search End Date:
Sort Order
Sources to include:
OR Message ID:
 

Display Mesage #110605


LED conversion difficulties
Written by tradewinds1964 on 2/13/2012 at 03:17 pm

Stop! Stop! You're getting me all excited and making everyone else jealous. Holy
snicker bars Batman, we could have a built in Uni-Go trailor butt. Oh my god
Susan. Look at that motorcycle's butt.

The bulb dropped straight in. It has a little chrome holder that it slides into.
That chrome holder fits just like the stock bulb with 3 little tabs for
alignment. Then when you flick from Hi to Low, the bulb either rest inside the
chrome holder or it pops up out of the chrome holder. But the movement is not
enough to touch anything. It all stays within the range of the chrome holder.
The ballast for the HID is about the size of a cassette case holder, maybe
smaller. The only mod I had to do was that the HID needs a direct line to the
battery. So, I ran a wire from my cigarette lighter to the light with a fuse in
between.

I have had no problems with glare. You can see the rectangle pattern on the
ground very close to where a typical bulb would hit when on Lo beam. I took
Goldwing Fred's advice and run my Hi beam during the day for extra visibility.

Built in projectors? I like it. And then we can have angel eyes. And and then we
can have side angel eyes under the footpegs. And then then then we can have
angel eyes in the top shelf looking up just like that beam on top of the Luxor
in Vegas. And with the extra trunk space, we can house an extra battery and gas
tank. And and and then with the leftover extra space, we can mod an extra
alternator so juice will never be a problem again.

Yeah! Yeah! Oh Yeah!!

Besides. Pimp-My-Motorcycle? What do you think PC stands for?
Pacific Coast? No No No my friend. Pimp Cycle baby!!!!!!!

Ting
Atlanta, GA
'90 Red PC
Glen Scotia(pronounced Sko-sha)

Message Thread for message #110605

douglasvanb
2/12/2012, 05:19 am
LED conversion difficulties
Hello Coasters, Thanks to a very frugal December (who needs to eat?!), I purchased LED replacement bulbs for every single bulb on my PC800. Over the last several days I installed all of the bulbs. The new bulbs look great and are as brigh

    kd5fdw
    2/12/2012, 03:48 pm
    LED conversion difficulties
    Doug [et al]: First, a question. What LEDs did you use in the tail/brake lights? I used an 1157(red) replacement and it's a bayonet style that shoots the light upward. At night it's OK, but other riders complain by day. I'm trying to

      douglasvanb
      2/12/2012, 04:56 pm
      LED conversion difficulties
      Dave, The bulbs I bought are as follows: 1157 brake lights (red): http://www.amazon.com/gp/product/B004C8L1AE/ 1157 turn signal lights (white):

      alfr4d
      2/13/2012, 06:34 pm
      LED conversion difficulties
      These are my taillights Dave, because they seem so much bigger. http://img232.imageshack.us/img232/5578/ledlampjes.jpg The lights were not red and they really have to b

        douglasvanb
        2/13/2012, 07:57 pm
        LED conversion difficulties
        Alfred, With respect to the T10 wedge-style base bulbs that are in the center license plate/ tail light position and behind every gauge in the instrument cluster, the bulbs I found (and linked to in a previous post) save 4 watts per bulb

          alfr4d
          3/6/2012, 08:09 pm
          LED conversion difficulties
          > > > First, a question. What LEDs did you use in the tail/brake lights? > > > Hi to everybody. http://img842.imageshack.us/slideshow/webplayer.p

            alfr4d
            3/29/2012, 02:38 am
            LED conversion difficulties
            Hello to all, Yesterday I mounted the same LED's as mentioned in the link below as nice for the licence-plate/taillight to the dashboard. I was expecting those long LED's would not fit in and also bought smaller but there was room enough

              alfr4d
              3/29/2012, 03:56 pm
              LED conversion difficulties
              I think I solved the problem with the LED dash-lights possibly able to sneak out of their rubber sockets and fall into the dash housing. Glue wont help, both the plastic and the rubber are not good material to have glue stuck on. I will pull

                douglasvanb
                3/29/2012, 05:49 pm
                LED conversion difficulties
                Alfred, That is a very strange problem. I think that we are using the same little lamps for the instrument panel. On my instrument panel, the lamps are held in place VERY well by the rubber boots. Fishing line sounds like a good solution

                  alfr4d
                  3/30/2012, 06:04 pm
                  LED conversion difficulties
                  I could push a match in if I wanted. For these long lights this is not right. The taillight was no problem glueing but the rubber is very slippery and I was right, the silicone did not stick much to it. Solved it today with two strands of

    kyle.mason66
    2/12/2012, 07:04 pm
    LED conversion difficulties
    Doug, I didn't change my turn signals over to LED, but I think you can use a relay in place of a resistor. Here is a web page example (not endorsing this web page or any particular product).

      douglasvanb
      2/12/2012, 09:22 pm
      LED conversion difficulties
      Kyle, Thank you for the link. I am going to give that company a call on Monday to see what they think. It appears that I might have toasted my self-cancel turn signal control unit (the thing buried inside of the steering stem). I'v

        tradewinds1964
        2/13/2012, 06:08 am
        LED conversion difficulties
        I used that same company to replace my instrument panel lights. Also used them for the interior lights in my car. They have a great product and I have no complaints with them. I do remember a while back that it was mentioned that the PC d

          douglasvanb
          2/13/2012, 06:17 am
          LED conversion difficulties
          Okay Ting... I'll bite... what HID kit would I theoretically use if I were to convert over to using HID? Would I need to worry about melting the plastic headlight housing? You're a bad influence on me! :-) Cheers, Douglas

            tradewinds1964
            2/13/2012, 06:46 am
            LED conversion difficulties
            I'm a bad influence? It was all the reading on your site that eventually paved the way to this site and then buying my PC. To blame me is to blame thyself sir! LOL! I have the 10,000 brightness kit for my bike. It uses the H4 bi Xenon bul

              douglasvanb
              2/13/2012, 06:52 am
              LED conversion difficulties
              Just wait until the two of us get picked up for one of those pimp-my-motorcycle cable tv shows... "no no! it needs MORE trunk!" Did you retrofit in a projector housing or did it drop straight in? I've seen plenty of cars that ha

                tradewinds1964
                2/13/2012, 03:17 pm
                LED conversion difficulties
                Stop! Stop! You're getting me all excited and making everyone else jealous. Holy snicker bars Batman, we could have a built in Uni-Go trailor butt. Oh my god Susan. Look at that motorcycle's butt. The bulb dropped straight in. It has a li