Search Messages

 
Author:
Search Start Date:
Search End Date:
Sort Order
Sources to include:
OR Message ID:
 

Display Mesage #95040


Throttle locks ?
Written by timdearborn on 7/15/2010 at 03:31 am

I just put mine on a few days ago. (Thanks for the pre-drilled hole, Gib.) When
I first put mine on, I also had some problems with the throttle releasing. After
tinkering with it for a while, it suddenly started releasing. While I thought it
was clear on both sides, I think a small part of the throttle grip was caught
under the throttle lock.

--- In ipcrc@yahoogroups.com, "ombestudio" <ombestudio@...> wrote:
>
> Ok, I won't ask... I pretty much have it working now. I think I'm going to
pick up a couple of those washers though and try that.
> Thanks for all the help.
>
> --- In ipcrc@yahoogroups.com, "Gib" <gibinmich@> wrote:
> >
> > Strange, something is not right. I think my adjustment screw is in about
four or five turns. Please don't ask me to check.
> >
> > --- In ipcrc@yahoogroups.com, "ombestudio" <ombestudio@> wrote:

Message Thread for message #95040

ombestudio
7/14/2010, 01:15 pm
Throttle locks ?
Hi guys, I'm kinda new around here and mostly a lurker. I do have a stupid problem and really need some help... so here goes. I have an '89 and bought a vista cruise throttle lock like I've done for all my past motorcycles. I can't get th

    goldwingman40
    7/14/2010, 03:33 pm
    Throttle locks ?
    Orrin, The bars on the PC are 7/8" at the ends, they are only 1" at the center where the clamps are. If the slot for the tab is not cut in the correct location and with a slight cnearance the unit can't float to canter itself on

      gibinmich
      7/14/2010, 07:17 pm
      Throttle locks ?
      Mine was binding up a little because I didn't drill the hole for the tab in the right location. I went to the hardware and bought a couple of 7/8 inch I.D. nylon washers and put one on each side to keep it away from the housing and the grip a

        ombestudio
        7/14/2010, 07:41 pm
        Throttle locks ?
        Thank you guys for the responses. I actually cut the tab off the throttle lock and figured I would just drill into the housing. I never got that far because I can't seem to position it where it isn't binding. As far as having the screw fo

          gibinmich
          7/14/2010, 07:54 pm
          Throttle locks ?
          Strange, something is not right. I think my adjustment screw is in about four or five turns. Please don't ask me to check. --- In

            ombestudio
            7/15/2010, 02:31 am
            Throttle locks ?
            Ok, I won't ask... I pretty much have it working now. I think I'm going to pick up a couple of those washers though and try that. Thanks for all the help. --- In

              timdearborn
              7/15/2010, 03:31 am
              Throttle locks ?
              I just put mine on a few days ago. (Thanks for the pre-drilled hole, Gib.) When I first put mine on, I also had some problems with the throttle releasing. After tinkering with it for a while, it suddenly started releasing. While I thought it

                gibinmich
                7/15/2010, 11:14 am
                Throttle locks ?
                When installing a Vista Cruise with the stock grips, the grip has to be pulled away from the housing just a little bit to make room for the Vista.....but then the grip hangs over and binds up on the bar end. I always trim the little ridge off