Search Messages

 
Author:
Search Start Date:
Search End Date:
Sort Order
Sources to include:
OR Message ID:
 

Display Mesage #98188


LED taillight
Written by douglasvanb on 10/25/2010 at 09:14 pm

What did you do to make the turn signals flash at the proper rate? Anything
special done so you don't burn out the self-canceling turn signal module?

And here I was trying to save money this fall! :-)

Cheers,

Douglas

--- In ipcrc@yahoogroups.com, "Alfred W" <alfred.wams@...> wrote:
>
>
>
> I have them for one season now and I am satisfied but would like to share on
how. the picture is at http://img232.imageshack.us/img232/5578/ledlampjes.jpg
>
> The colorless and bright light is half in-between red and amber trough the red
lens. Some have had better results with red LED light behind a red lens. The
next time I will try. Go for red.
>
> Taillight is best to be seen at night but anyway I found the taillight
function to be not enough light. Brake light however is by far bright enough.
This is a problem of design. The yellow dots have three chips each so I figure
they have only one working for a good difference when applying the brake. I have
a new license plate light because they do go black slowly and cleaned the
hidden, window underneath the lens, that shines at the license plate. This way
you will have a good red taillight in the middle as it should and still a good
visibility.
>
> You must buy a combined Tail-Brake function light and be aware that some bulbs
are provided with more electricity and may mistakenly be advertised as such.
They should have two contacts at the end. One from the two I received had wrong
attached wires and was always braking. I got another after photographic proof it
was a swap and was allowed to keep the wrong wired, but still usable light. Best
service ever.
>
> Together with the headlight switch that I made I canceled a lot of load but
have really no idea how much for the taillights. Some say LED reacts more quick
(applies to the front brake switch only) but I think this is not noticeable at
all.
>
> --- In ipcrc@yahoogroups.com, "aek_alex" <aek_alex@> wrote:
> >
> > Has anyone used different bulbs for taillights?
> >
> > May some bright flashing ones.
> >
> > Any suggestions on brighter LED Bulbs?
> >
> > I want to be a little safer by doing this.
> >
> > Thanks,
> > Alex
> >
>

Message Thread for message #98188

aek_alex
10/25/2010, 01:38 am
LED taillight
Has anyone used different bulbs for taillights? May some bright flashing ones. Any suggestions on brighter LED Bulbs? I want to be a little safer by doing this. Thanks, Alex

    douglasvanb
    10/25/2010, 02:11 am
    LED taillight
    I looked into LED bulbs for the tail lights and turn signals late last year. From what I saw then, I wasn't comfortable with using any of them as drop-in replacements on my PC. Various problems like fit, the way the light is delivered, etc,

      csury
      10/25/2010, 02:48 am
      LED taillight
      I want to use LEDs where I can so as to maximize power available for battery charging and accessories. These 68-LED towers work well in the rear turn signals. h

    goldwingman40
    10/25/2010, 04:18 am
    LED taillight
    Alex, I use #2357 bulbs in the tailights to be a little brighter and for the center light I went to the larger diameter bulb, I think it might be #905 but not sure and am not up in the shop, for higher output equal to the tailights. Fre

    waynedoenges
    10/25/2010, 11:38 am
    LED taillight
    I have LED brake and turn signal lights. I love them. The brake lights flash 20 times a second for 2 seconds and than go solid. I saved a full volt on my voltmeter with them. I plan on replacing the licence plate and rear turn signal lights t

    alfr4d
    10/25/2010, 09:03 pm
    LED taillight
    I have them for one season now and I am satisfied but would like to share on how. the picture is at http://img232.imageshack.us/img232/5578/ledlampjes.jpg The color

      douglasvanb
      10/25/2010, 09:14 pm
      LED taillight
      What did you do to make the turn signals flash at the proper rate? Anything special done so you don't burn out the self-canceling turn signal module? And here I was trying to save money this fall! :-) Cheers, Douglas ---

        dl_page
        10/26/2010, 07:45 pm
        LED taillight
        For info, I bought a series of LED signal and running/break lights. Thank you Ebay Hong Kong... For the running lights, no problems (except a bulb I badly installed fell out of the holder and I spent 40 minutes and swearwords in 2 languag

          wkaufmann2000
          10/26/2010, 07:58 pm
          LED taillight
          Am 26.10.2010 21:45, schrieb dl_page: > > The turn indicators were sold as "containing resistors to work with indicator relay", though in practice, my indicators work at about 120 flashes per minute (ok, still legal - barel

            dl_page
            10/26/2010, 08:10 pm
            LED taillight
            Hum.... are you sure about that? If you have less load on the circuit (for example a blown bulb that is now open circuit), half the load=twice the flashing speed. Surely you want to increase the load to drop the speed down? Cheers, Dan

              wkaufmann2000
              10/26/2010, 08:53 pm
              LED taillight
              Daniel, I am pretty sure ! Of course you want to increase the load, but you do this by lowering the total resistance (=parallel) so that more current can flow, not by increasing the total resistance (= in line). If you have

                dl_page
                10/26/2010, 10:21 pm
                LED taillight
                Wolfgang, It's late and i'm getting confused, you are correct. I'm sorry :) Adding a resistor in series would work, but it would also drop the voltage to the LED and make the bulb less bright - not good for a safety feature! Th